I honestly think this is the worst use case for a 3d printer. The part isn’t improved by printing. You can buy the part easily. The cost of modelling time and printing is more than the replacement. There’s a decent chance the replacement part would have arrived quicker than the print took… Sorry to be a bore, it’s better than an octopus or another benchy, I’ll give you that.

Nice

It’s not just weight but friction. Depending on the flooring you could add a rubber pad to the bottom of the piece to help. If you do go the cavity route, steel washers are pretty cheap and would be heavy, or as someone else suggested, some lead weights will work.

For every self help group there are hundreds of forums for hate speech. For every open, sane discussion there are hundreds of discussions that are railroaded by trolls. I agree that a transparent state is brilliant, but the reason for transparency is accountability and the individual needs to have that accountability also.

So few people care about this that it’s never going to stop. There are far more negatives to be solved by reducing anonymity than the positives of keeping a semblance of privacy.

Nice, how different does it sound to a modern one?

I saw a tip for paint recently that I haven’t tried yet, but it might work here too. If you get some painters tape and make a V over the top it acts as a spout and it never gets on the threads

Link to image

I have 4 of these. Two of them are the ones that have integrated water catchers and only overflow if they are overwatered. One I’ve put a saucer in with the pot and one I just have to put a towel under it. I’d say the best option is the one with a saucer, you can visibly see that it’s flowed through, you can add gravel to improve humidity.

A quick search for 2 channel 24v fan controller yealded the below link. Not saying this is ideal for your scenario but something similar will work and can be powered with a power brick. Doesn’t look like it comes with instructions though so I’m not sure what current it requires. The temperature sensor could work to make it turn on when the printer heats up as well.

https://www.amazon.co.uk/Channel-Temperature-Controller-Governor-Display/dp/B083R97GZ1

Because they didn’t actually live in caves that often.

The image of these people living in caves arises from the fact that caves are where the preponderance of artifacts have been found from European Stone Age cultures. However, this most likely reflects the degree of preservation that caves provide over the millennia, rather than an indication of them being a typical form of shelter. Until the last glacial period, the great majority of humans did not live in caves, as nomadic hunter-gatherer tribes lived in a variety of temporary structures, such as tents[4] and wooden huts (e.g., at Ohalo). A few genuine cave dwellings did exist, however, such as at Mount Carmel in Israel.>

Wikipedia - Caveman

I think it’s all education. If people understand that credential managers are easier and safer then there would be a lot more uptake.

I disagree that the main reason is thermal runaway. It is more likely to be underrated components that can’t handle the current. This would not be immediately apparent and does usually come from lower quality printers.

I agree, I’m looking for immersion and story. That said, I’m also willing to wait a few months for devs to fix all the bugs they should have removed before the rushed release dates.

The other comments have this covered but bare in mind that if you’re in the northern hemisphere we are heading in to the dormant season and it will require even less water.

I think it’s the PH part from some other comments but I can confidently say the moisture part works pretty well. I have been using one for about a year and it’s been helpful.

I loath getting on my high horse, but don’t take things from forests unless they are explicitly there for the taking or you have permission from someone. The odd small item here and there may not seem significant but if everybody did it it would have a significant impact.

Voron allow you to configure a printer and the provide a spreadsheet suggesting the sources for buying the parts. They aren’t region specific but most of the vendors are multinational.

This is my course of action with anything I buy.

1. Is there an ethical source
2. Is there a second hand source
3. Is there a EU company that may source the manufacture in China
4. Rarely, buy the Chinese one

Anyone know off hand if liquid seaweed covers all these bases?

I haven’t had any problems.